1-20 ton gas/oil fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2 Mpa
Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
7-70 MW gas/oil fired hot water boiler
Capacity: 7-70 MW
Pressure: 1.0-1.6 Mpa
Fuel: Nature gas, coke oven gas, blast furnace gas, carbon black off-gas, biogas, methanol, LPG, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, hospital, colleges and universities.
2.8-29mw coal fired boiler
Capacity: 2.8-29mw
Pressure: 1.0-1.25 Mpa
Fuel: Bituminous coal, lean coal, anthracite
Industries: Heating, hotels, schools, hospitals
horizontal thermal fluid heater
Capacity: 700 - 14000 kw
Pressure: 0.8 - 1.0 Mpa
Fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil
Industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries
1-20 ton biomass fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2.5 Mpa
Fuel: Biomass particles
Industries: Heating, chemical, food, tobacco, textile, printing and dyeing, feed, medicine, building material, wine, rubber, hospital

Testing and Commissioning Procedure for Steam Boiler and
17 Dec 2007 4.2.4 Hot Water Steam . 4.2.5 Steam Boilers . 4.2.6 Complete Steam & Boiler System. 4.3 Commissioning and Statutory Inspections. 4.3.1 Steam

Steam and Condensate - A basic overview of a steam system - The
Steam boilers are usually operated under pressure, so that more steam can be Heating the water in the feedtank also reduces the amount of dissolved oxygen in it. This process can be carried out by an automatic system which uses either a probe Insulation fitted around the pipe will reduce this heat loss considerably.

Steam Lines Flushing: The Why and How - Forbes Marshall
Process lines where operational difficulties will be caused because of presence of water . 2. Instrument service lines should be service tested and blown with air.

Best Practices for Condensate Removal on Steam Lines | TLV - A
Traps should be installed at 30 to 50 meter (100 to 160 feet) intervals on a steam line . In Front of Pressure Reducing Valves and Control Valves. In Front of Manual Valves Closed for a Long Time. At the Bottom of Vertical Lifts or Drops. Correct by Piping set at an incline. Removing Air for Steam Lines .

Brief Accident Cases of Boilers and Pressure Vessels in Hong Kong
pipe that will convey oils, steam or water under pressure to or from the boiler , as . water with incorrect procedure during the rinsing process resulted in hot fluid

Guide to Operation of Steam Receivers
Boilers and Pressure Vessels Division of the Occupational Safety and. Health Branch as Guide to. Operation of Steam Receivers, published by the Labour Department. and covers equipment such as a vessel used to store steam for heating of . To prevent water hammer in steam pipe , open the drain valve to drain the.

Best Practices for Condensate System Piping - Plant Engineering
10 May 2011 The best method for improving steam system energy efficiency, reducing costs is to return the maximum quantity of condensate to the boiler plant. Although condensate is hot water , sizing a condensate line as if it were hot

Water hammer in steam systems: cause and effect - Plant Engineering
1 Sep 2006 Heat transfer systems in almost any form hot water , high temperature Proper steam system design, installation, operation and Fracturing of pipes or steam system components can propel fragments that can cause injury or loss of life. of boiler water into the steam main, overwhelming the steam traps.

Necessity of Steam Condensate Removal | Yoshitake Inc.
Necessity of Steam Condensate Removal and Its Procedure . Condensate generates in steam transport pipe by heat release. If there is no warmer in the boiler , steam left from the boiler usually has 2% of moisture. Moreover, carry-over To prevent such water hammer, sufficient condensate removal is required. Condensate

( PDF ) Selection and Analysis of Material for Boiler Pipes in a Steam
22 Aug 2016 The problems of a material selection for making the boiler pipes in a .. feeding water temperature (130 ºC), boiler's heating surface (5667 m2)

Design of Steam Heating Systems - Engineering ToolBox
Single Pipe Steam System with Main Pipes Pitched Towards the Boiler steam ; Hot Water Heating Systems - Steel Pipes Pressure Loss Chart - Steel pipes in Steam Heating Process - Load Calculating - Calculating the amount of steam in

Designing An Efficient Industrial Steam System - YouTube
31 Oct 2015 - 14 min - Uploaded by Mead O'Brien Steam systems consist of 4 basic components: the boiler , the distribution piping , the heat

Low Water Protection For Boilers - AXA XL
enters a severely overheated boiler , the water will flash to steam . The weakened LWFCO. Do not install any piping that allows feedwater to flow through the cutout device. . Hot water boilers are always filled with water during operation .

Boiler Efficiency and Steam Quality: The Challenge of Creating
And if a puddle of water is allowed to accumulate in steam pipes , it will eventually In a simplified explanation of boiler operation , a hot heat -transfer surface is

Water Still Flashes to Steam at 212 - The National Board of Boiler
Over the long weekend the steam condensed and the hot water accumulated Experience tells us, therefore, that the inside of the pipe was cherry red to hot white. Always use proper welding procedures qualified in accordance with ASME

Boiler control basics - Control Components
You see, a steam boiler needs its water to move the heat away from its level of water , heat quickly accumulates. Too much Because the water is in the system piping and radiating during operation , the normal water level becomes a point.

steam systems - Cleaver-Brooks
condensate return/ water piping system, and a steam -use facility (Figure 1). In this feedwater systems, heat exchangers (e.g., economizers), boiler and system controls, Categorize the application and load as heating /cooling, process or

Steam , Hot Water and Process Heating Systems - Sustainability
Heat loss from uninsulated piping . 13. Table 4: energy efficiency in boilers , steam systems, hot water .. The most effective repairs on steam pipe leaks can be.