1-20 ton gas/oil fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2 Mpa
Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
7-70 MW gas/oil fired hot water boiler
Capacity: 7-70 MW
Pressure: 1.0-1.6 Mpa
Fuel: Nature gas, coke oven gas, blast furnace gas, carbon black off-gas, biogas, methanol, LPG, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, hospital, colleges and universities.
2.8-29mw coal fired boiler
Pressure: 1.0-1.25 Mpa
Fuel: Bituminous coal, lean coal, anthracite
Industries: Heating, hotels, schools, hospitals
horizontal thermal fluid heater
Capacity: 700 - 14000 kw
Pressure: 0.8 - 1.0 Mpa
Fuel: natural gas, coke oven gas, bio-gas，liquid propane gas, diesel, heavy oil, light oil, crude oil
Industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries
1-20 ton biomass fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2.5 Mpa
Fuel: Biomass particles
Industries: Heating, chemical, food, tobacco, textile, printing and dyeing, feed, medicine, building material, wine, rubber, hospital
shell boilers - SAFed
This edition was revised in 2012 by SAFed to update references to standards and that over 10 % of boilers tested in 1995 exhibited cracks at the furnace and pressurised hot water shell boilers - as well as steam boilers - suffered from cracking .. of large diameter stay tubes as opposed to the more conventional stay bar
Pressure Vessels - processdesign
Codes for pressure vessels can be found in the ASME Boiler and Pressure experience a pressure difference of greater than 0.5 bar can be classified as pressure vessels. Pressure vessels with a wall- thickness :diameter ratio of less than 1: 10 can Pressure vessels typically consist of a cylindrical shell and elliptical or
CONSTRUCTION CODE FOR BOILERS Notification No.197 of - ILO
30 Apr 2003 Head Plates and Flat Plates (Articles 10 through 14) temperature of steam or a liquid in the boiler , while for heating vessels (General standard )) and materials with . The plate thickness of the shell of any water tube boiler to which . The sectional area of stay bolts, bar stays, stay tubes, and gusset
Boiler Questions - Marine steam boilers
If you have a diesel engine exhaust gas economizer then 7 bar boiler pressure Pipe thickness reduction of the shell side outlet pipe is observed for last couple of years. . Install a five to ten minutes' time-delay in the fan-motor stop function.
Code of Practice for the Safe Operation of Electric Steam Boilers
10 . CHAPTER TWO. 2.1 Types of Electric Steam Boilers . 12. 2.1.1 Electrode compliance of all maker's instructions, relevant codes and standards .. the pressure range of 0 - 15 bar are: - . especially dangerous as it corrodes the shell rapidly. .. proportionally reduced by an increase in the thickness of the solid, and.
Thermodynamic Design of a FireTube Steam Boiler - osu.edu
5000 kg of steam per hour and a operating pressure of 10 bar . The Figure below equations shows a standard three pass fire tube steam boiler system used as a template for our engineering Main Shell Thickness = 0.012 m. Furnace Plate
DNV Ship rules Pt.4 Ch.7 - Boilers , Pressure Vessels, Thermal-Oil
However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in .. Valves on pressure vessels other than boilers and steam - .. p = design pressure in bar , Di = internal diameter in mm, t = shell thickness in mm. Certification can be based on a standard recognised by the So-.
DNVGL-RU-SHIP Pt.4 Ch.7 Pressure equipment - Rules and
[2.6.2]. Sec.4 [2.6.1]: minimum thickness of shells and dished ends Location for the installation of safety valves at steam boilers pressure above 0.5 bar . requirements of the rules for classification of ships Pt.6 Ch.4 Sec. 10 and Ch.6 Sec.6. .. Dimension. Issued by. Certification standard . Pressure equipment class II.
Mechanical Code B3.3.1.01 BOILER CODE - ATHRA
12 Dec 2006 Reformatted to FRONZ standard and minor errors corrected. straps of each required thickness shall be cut from one plate. 10 . BAR STAYS. Where plus threads are used, the ends of the stays may be upset or the middle internal steam /waterside surfaces of the boiler shell end plates, fire box,.
Shell Boilers - Spirax Sarco
Overview of the different types of shell boiler with layouts, heat and steam Figures 3.2.1a and 3.2.1b show a typical two-pass boiler configuration. . A compromise is reached with a furnace tube wall thickness of between 18 mm and 20 mm. This translates to a practical pressure limit for shell boilers of around 27 bar .
Indian Boilers Regulations - 1950 - DIPP
Reg.7, Boiler Shells not in Accordance with Standard Conditions. Reg.8, Use of Welding. Reg.9, Process of manufacture. Reg. 10 , Chemical Analysis Reg.106, Thickness of Shell Angle Rings Reg.115, End Plates in steam spaces Reg. 199, Bar or bulb stiffened end plates and smoke-box tube plates of Loco-type
Design and Analysis of Boiler Pressure Vessels based - IOPscience
One of the Standards followed in designing Pressure Parts is ASME (American producing steam at a pressure of generally 2 bar and higher. Fire or smoke or flue tube or shell -type boilers in which flue gases are inside and water is . thickness of Header based on Design Pressure and Temperature is the main criteria
The Feedtank and Feedwater Conditioning - Spirax Sarco
The standard dosing rate for sodium sulphite is 8 ppm per 1 ppm of dissolved oxygen. . Figure 3.11.5(a) shows the formation of steam at 10 bar g when the boiler is should be sought in selecting the correct material and economic thickness . British Standards BS 2486 recommends pH 10.5 - 12.0 for shell boilers @ 10
Design, Construction, Installation and Use of Boilers and Pressure
1 Jan 2007 (s) high pressure boiler means a boiler designed for a steam pressure (z) miniature boiler means a boiler having a shell with an inside . considered as being the equivalent of 10 square feet of heating surface as defined . blueprints and specifications shall indicate all sizes and thicknesses of metal,.
FLO1060, oil or gas fired steam boiler - Jumag Steam Generators
Jumag oil or gas fired steam boilers link the advantages of a compact quick steam Vertical vaporization system similar to a shell boiler with wall thickness up to 11 High standard of quality, due to the use of industrial standard components Operating pressure up to 13 bars , working pressure is 5 bars to 11 bars ; Only
An Analysis of New Boiler Technologies - Thermal Energy Systems
saturated steam temperature [ boiler operating pressure] the more that electricity is Higher pressures require thicker metal thicknesses to contain that pressure but the In general, engineers tend to think of pressure in 10 or 20 bar stages so we have seen HP . In the case of drums it typically requires a thicker shell to.